Connecting with the device to the System (Laptop/Desktop)

To log in to SILBO_IAB44-C by connecting the router to your laptop or desktop via LAN or using Wi-Fi, please follow the steps below.

Connecting via LAN:

Connect your laptop's LAN port to one of the router's LAN interfaces. Ensure that you select any LAN interface (there is one available) while making sure the WAN interface is not used.

How to connect with the SILBO_IAB44-C application

Once the LAN connection is established between the device and the laptop or the desktop

Please open the command prompt and ping to get the IP config of that device.

Type the command Ipconfig

It will provide the Ip address/url of that device through which the application can be accessed.

Log In

Open the web browser and type the IP address in the URL.

It will show the log in page of the application.

Give the valid credentials for the username and password to login to the application page.

Once the user credentials are provided it will direct to the landing page of the application.

The “Status” landing page shows all the detailed specification of the device like system, memory storage and connection tracking etc.

The application is divided in to 8 Modules.

Info
Settings
Maintenance
Status
Features
Configuration
Appmanager
Logout

1. Info

The “Info” module provides the information about the devices to the user.

It provides all the specification related to the hardware, firmware, Networks and the Connection uptimes.

It has 3 submodules.

Overview
System Log
Kernel Log

1.1 Overview

In overview module it displays all the specification categorically of a device like System, Memory, storage, Connection tracking, DHCP Lease.

System:

In this section it displays the hardware configured specification of the device.

The specifications details are as follows,

SN	Field name	Sample value	Description
1	Hostname	37A26230014	This field displays the router serial number of the device
2	Model	Silbo_IAB44-C_GW-EC200A	This field displays the model number of the device
3	Firmware Version and IPK Version	1.16_1.13_RC3	This field displays the firmware version and IPK version
4	Application Firmware version and IPK version	1.02_1.06	This field displays the software version of the device.
5	Kernel Version	4.14.180	This field displays the kernel version of the device
6	Local Time	Friday, July 19, 2024 at 11:52:23 AM	This field displays the local time
7	Uptime	1h 48m 3s	This field displays the uptime of the device
8	Load Average	0.66 0.29 0.17	This field displays the average load

Memory:

In this section it displays the memory configured specification of the device.

The specifications details are as follows.

SN	Field name	Sample value	Description
1	Total Available	57716 kB / 124188 kB (46%)	This field displays the total availability of memory space in the device
2	Free	46424 kB / 124188 kB (37%)	This field displays the Free memory space in the device
3	Cached	444 kB / 124188 kB (0%)	This field displays the Cached memory space in the device
4	Buffered	11224 kB / 124188 kB (9%)	This field displays the Buffered memory space in the device

Storage:

In this section it displays the status of storage as root and temporary usage specification of the device.

The specifications details are as follows.

SN	Field name	Sample value	Description
1	Root Usage	1580 kB / 12800 kB (12%)	This field displays the total root usage of the device
2	Temporary Usage	444 kB / 62092 kB (0%)	This field displays the total temporary usage of the device

Network:

In this section you can monitor IPv4 WAN status.

The specifications details are as follows.

SN	Field Name	Sample value	Description
1	Type	DHCP client	A DHCP client is a device or software that requests and receives configuration information from a DHCP server, such as an IP address, gateway, and DNS servers.
2	Connected	1h 49m 8s	This indicates the duration for which the device has been connected to the network.
3	Address	10.62.35.111	This is the IP address assigned to the DHCP client by the DHCP server. It uniquely identifies the device on the network.
4	Gateway	10.62.35.144	The gateway (or default gateway) is the IP address of the network device that routes traffic from the local network to other networks.
5	DNS	8.8.8.8, 10.103.81.232	The first DNS server "8.8.8.8" is a public DNS server provided by Google. The second DNS server "10.103.81.232" is a private DNS server.

Active SIM Information:

This section displays SIM details only when the SIM card is active.

Connection Tracking:

In this section it displays the status of connection tracking for the device.

The specifications details are as follows.

SN	Field Value	Sample Value	Description
1	Active Connections	48/16384 (0%)	This field displays the active connection of the device.

DHCP Leases:

In this section it displays the DHCP lease of the temporary assignment of an IP address to a device on the network.

The specifications details are below.

SN	Field name	Sample value	Description
1	Host Name	KermaniK-LT	This field displays the configured Host Name/Username for that device.
2	IPv4-Address	192.168.10.147	This field displays the IP address of the device.
3	MAC-Address	34:73:5a:bb: ab:7a	This field displays the MAC-Address of the device.
4	Lease time remaining	11h 53m 49s	This field displays the lease time remaining for the device.

1.2 System Log

This page provides on screen System logging information. In this page the user gets to view the system logs.

1.3 Kernel Log

This page provides on screen Kernel logging information.

In this page the user gets to view the Kernel logs.

2. Setting

In this “Setting” module the user can Configure/update all the required parameters related to Network, SIM Switch, Internet, VPN, Firewall, Loopback Rule, Remote monitoring, Tunnel as per requirement.

IT consist of 8 submodules.

Network
Sim Switch
Internet
VPN
Firewall
Loopback Rule
Remote Monitoring
Tunnel

2.1 Network

In this section the user does all the setting related configuration with reference to network like Ethernet Setting, Cellular Setting, Band lock and Operator Lock, Wi-Fi, Guest Wi-Fi, Wireless Schedule, SMS Setting, Loopback IP.

Ethernet Setting:

In this page it will display all the configured port that is attached with the device.

For this device 2 ports are configured. Ethernet mode can be configured as WAN and as LAN as well. Ethernet LAN Connection settings can be configured as DHCP server or Static.

For port 2 settings,

Port 2 is convertible from WAN to LAN while EWAN2(WAN) stays by default.

Note: After any changes made, save and update the page below.

SW_LAN settings,

In this part the user can configure the setting for SW_LAN.

Note: After any changes made, save and update the page below.

The specifications details are below.

SN	Field name	Sample value	Description
1	SW_LAN Ethernet Protocol	DHCP Server	This field displays the Ethernet mode selection.
2	SW_LAN DHCP Server IP	192.168.10.1	This field displays DHCP server IP configured which can be changed accordingly.
3	SW_LAN DHCP Netmask	255.255.255.0	This field displays DHCP server Netmask address configured.
4	SW_LAN DHCP Start Address	100	This field displays DHCP server start address configured.
5	SW_LAN DHCP Limit	50	This field displays DHCP server limit.
6	DNS Server	1	This filed display number of DNS server availability.
7	DNS Server Address	8.8.8.8	This filed display the DNS server address.

After configuring all the required information, the user should click on the save and then click on the update to update the all the required information.

Static option for SW_LAN Ethernet Protocol:

Select the option of static from the drop-down menu for SW_LAN Ethernet Protocol.

Note: After any changes made, save and update the page below.

The specifications details are below.

SN	Field name	Sample value	Description
1	SW_LAN Ethernet Protocol	Static	This field displays the Ethernet mode selection
2	SW_LAN static IP	192.168.5.1	This field displays static server IP configured.
3	SW_LAN Netmask	255.255.255.0	This field displays static server Netmask address configured
4	DNS Server	1	This filed display number of DSN server availability
5	DSN Server Address	8.8.8.8	This filed display the DSN server address.

After configuring all the required information, the user should click on the save and then click on the update to update the all the required information.

Cellular Setting:

In this page, the user needs to configure the various details with respect to the SIM.

Select single cellular single sim where the user must configure the APN details of the sim used for the router device. The Configurations can be done based on the SIM usage, with respect to IPV4 or IPV6.

The specifications details are below.

SN	Field name	Sample value	Description
1	Cellular Enable	Checkbox	Check this box to enable cellular functionality.
2	Cellular Operation Mode	1.) Single Cellular with Dual Sim 2.) Single Cellular with Single SIM	1.) This mode allows you to use one cellular modem with two SIM cards. 2.) This mode allows you to use one cellular modem with single SIM card.
3	Cellular Modem 1	QuectelEC200A	This field displays the modem name.
4	Choose SIM 1 APN Mode	1.) Auto 2.) Manual	1.) Choose Auto for regular SIM to detect APN name automatically. 2.) Choose manual to enter the APN settings manually in case of M2M SIM cards.
5	SIM 1 Access Point Name	airtelgprs.com	Enter the APN provided by your cellular service provider in case of M2M sim. For regular sim cards APN name will be displayed automatically.
6	SIM 1 PDP Type	IPV4	Choose the PDP type, which is typically either IPv4 or IPv6 depending on the sim card.
7	SIM 1 Username		Enter the username if required by the APN. Leave blank if not required.
8	SIM 1 Password		Enter the password if required by the APN. Leave blank if not required.
9	SIM 1 Authentication Protocol	None	Choose the authentication protocol. Options typically include None, PAP, or CHAP.
10	Choose SIM 2 APN Mode	1.) Auto 2.) Manual	1.) Choose Auto for regular SIM to detect APN name automatically. 2.) Choose manual to enter the APN settings manually in case of M2M SIM cards.
11	SIM 2 Access Point Name	airtelgprs.com	Enter the APN provided by your cellular service provider in case of M2M sim. For regular sim cards APN name will be displayed automatically.
12	SIM 2 PDP Type	IPV4	Choose the PDP type, which is typically either IPv4 or IPv6 depending on the sim card.
13	SIM 2 Username		Enter the username if required by the APN. Leave blank if not required.
14	SIM 2 Password		Enter the password if required by the APN. Leave blank if not required.
15	SIM 2 Authentication Protocol	None	Choose the authentication protocol. Options typically include None, PAP, or CHAP.
16	Primary SIM Switchback Time (In Minutes)	10	Enter the time in minutes after which the system should switch back to the primary SIM if it becomes available.

After configuring all the required information, the user should click on the save and then click on the update to update the all the required information.

Band lock and Operator Lock:

In this page, the user needs to configure the lock band and operator based on the service provider.

Bands available in the drop-down list.

2G/3G option:

2G/3G: - 3G allows additional features such as mobile internet access, video calls and mobile TV. While the main function of 2G technology is the transmission of information through voice calls.

The user should select the band check box available for 2g/3g from the given list. Bands available for selection under LTE for the bands available in that area.

Operator Selection Mode:

The user needs to click on the check box of the “operator select enable” to select the operator.

Once the check box is clicked there will be a dropdown list of the operator modes from which the user needs to select the mode. The user needs to select the operator mode from the given dropdown list.

If the user selects the mode “Manual” or “Manual-Automatic” then one more text box will appear where the user must provide the operator code.

After configuring all the required information, the user should click on the save and then click on the update to update the all the required information.

Wi-Fi Setting:

In this, router has the general setting and change country code, channel, radio mode, radio passphrase as per the requirement after clicking on enable Radio button.

The user needs to select the respective radio mode based on its need.

It has 3 radio modes.

‘Access point’, ‘client only’ and ‘Access point and client’

Refer the below picture.

Access Point mode:

In Access Point mode, a configuration in which a router, allows wireless devices to connect to a wired network by creating a Wi-Fi hotspot.

Client point:

In client mode, the access point connects your wired devices to a wireless network. This mode is suitable when you have a wired device with an Ethernet port and no wireless capability, for example, a smart TV, Media Player, or Game console and you want to connect it to the internet wirelessly, select the Client Mode and give the Radio SSID & client passphrase.

Access point and client point:

Select this option for both type of connection, give both SSID and passphrase.

After configuring all the required information, the user should click on the save and then click on the update to update the all the required information.

The specifications details are below.

SN	Field name	Sample value	Description
1	Radio 0 Protocol	IEEE 802.11 b/g/n	This section shows the radio protocol which is by default.
2	Country Code	INDIA	Select the country accordingly. (INDIA by default)
3	Channel	Auto	In this dropdown the user should select the proper channel to be used. (Auto by default)
4	TX Power	100	In this text box the user should specify the power.
5	Channel Width	20 MHz	In this dropdown the user should select the channel width
6	Radio Mode	1.) Access point 2.) Client only 3.) Access point and client	In this drop down the user should select the mode. (Access point by default)
7	Radio SSID	AP_37A26230014	In this text box the user should specify the SSID number which usually comes with the router.
8	Radio Authentication	WPA2 Personal (PSK)	In this dropdown the user should select the type of authentication. (WPA2 Personal (PSK) by default)
9	Radio Encryption	AES	In this dropdown the user should select the type of encryption required. (AES by default)
10	Radio Passphrase	*********	In this text box the user should specify the password. Password will be given with the router which can be changed later.
11	Radio DHCP server IP	192.168.100.1	In this text box the user should specify the IP address of DHCP server. (192.168.100.1 will be default which can be changed accordingly)
12	Radio DHCP start address	100	In this text box the user should specify the start address of the DHCP. (100 value is default)
13	Radio DHCP limit	50	In this text box the user should specify the limit for the DHCP. (50 value is default)

Wireless Schedule:

Wi-Fi can be automatically withdrawn based on the configuration done in this section.

The user can schedule the Wi-Fi’s accessibility time during a particular period.

Note: This section is turned off by default, tick the box to activate it.

After configuring all the required information, the user should click on save and then click on update to update all the required information.

The user can select more than one “day of the week” for scheduling the Wi-Fi working hours.

Loop back IP settings:

The loopback IP address, often referred to as “localhost.” it is used to establish network connections within the same device for testing and troubleshooting purpose.

The loopback IP address, commonly represented as 127.0.0.1, is a special address used for testing network connectivity on a local machine.

It allows a device to send network messages to itself without involving external networks, making it useful for troubleshooting and diagnostics.

However, this IP can be changed as per requirement and to do that, Navigating to Setting>>Network configuration>> Loopback IP settings can be changed/updated.

After configuring all the required information, the user should click on the save and then click on the update to update the all the required information.

SMS Settings:

User needs to enable SMS option in SMS settings page.

This option is to validate the mobile numbers using which controlling commands could be sent to the router device.

1 to 5 mobile numbers can be authenticated by choosing from “Select Valid SMS user numbers” and adding the mobile numbers below respectively.

API key is the pass key used in the commands while sending SMS.

Displayed in the below screen is the default API key which can be edited and changed as per choice. After addition of the mobile number’s user needs to click on save button for changes to take place.

1.) Select valid user number max. 5 and add authorized phone number in the tab where you want to find the alert and click on ‘SMS Response Enable’, ‘save’ and ‘update’ button.

2.) Now send SMS commands from the configured mobile number.

3.) Once the commands are received from the user phone number the board will send acknowledgement as per the commands.

4.) After that it will send the router’s status once it has rebooted and is operational again.

Mentioned below are a few commands which can be sent from the configured mobile number to the router device. Below two commands are One for rebooting the router device and another to get the uptime.

1) {"device”: ["passkey”, “API key"],"command":"reboot","arguments":"hardware"}

2) {"device”: ["passkey ","API key"],"command”: “uptime"}

After configuring all the required information, the user should click on save and then click on update to update all the required information.